Hello Everyone. I need your help please 🙏

If you want to ask questions about how the machine works, peculiar details, the differences between models, here it is !
How to program the oric hardware (VIA, FDC, ...) is also welcome.
User avatar
ManicMiner1977
Private
Posts: 7
Joined: Thu Oct 24, 2024 2:23 pm

Hello Everyone. I need your help please 🙏

Post by ManicMiner1977 »

Hi everyone,

Thank you for letting me join your forum and in advance of your help.

I have a faulty Oric Atmos I recently bought from Ebay. It refuses to boot to BASIC and instead sits on a red/black barred screen. Reset button doesn't do anything.

Original PSU putting out 12v DC @ 3.5A.

Replaced all socketed RAM and checked original in Commodore Plus 4. Multiple diagnostic and use suggests OK.

Replaced ROM with 1.22 UK/ Diagnostic.

Tried a BBC Micro Model B 6502 CPU. No difference. CPU good in BBC afterwards. Replaced with original 6502. Tried bridging pin 1 and 40 as recommended reset to overcome c21 issue.

Found an apparently faulty Capacitor @ c23. Not sure of purpose of this but blown top and powdered on legs. Removed in anticipation of replacing.

Tried without this capacitor and get a different screen with more colours which changes on every subsequent power up.

Please see attached pictures. Last is original from Ebay. First is after removing c23 Capacitor.

Please can someone point me in the right direction before I start with a multimeter tracing around the board?

Best regards

Gavin.
Attachments
1000003373.jpg
1000003374.jpg
EBAY Original
EBAY Original
User avatar
iss
Wing Commander
Posts: 1706
Joined: Sat Apr 03, 2010 5:43 pm
Location: Bulgaria
Contact:

Re: Hello Everyone. I need your help please 🙏

Post by iss »

ManicMiner1977 wrote: Thu Oct 24, 2024 3:09 pm...
Welcome here!
Check: both multiplexers '257 (IC8,IC20), tracks with continuity tester.
Measure the resistance between 5V and GND rails (anywhere but after the 7905) - it should to be ~250 Ohms.
User avatar
Dbug
Site Admin
Posts: 4812
Joined: Fri Jan 06, 2006 10:00 pm
Location: Oslo, Norway
Contact:

Re: Hello Everyone. I need your help please 🙏

Post by Dbug »

ManicMiner1977 wrote: Thu Oct 24, 2024 3:09 pm Original PSU putting out 12v DC @ 3.5A.
That seems quite high, already with the standard 9V PSU the Oric voltage regulator gets easily burning hot, so it's definitely not an original PSU, or it is not working as expected.

Regarding the direction, Is it center positive?
User avatar
Chema
Game master
Posts: 3111
Joined: Tue Jan 17, 2006 10:55 am
Location: Gijón, SPAIN
Contact:

Re: Hello Everyone. I need your help please 🙏

Post by Chema »

Maybe it's stupid, but all that red instead of white while using RGB output... doesn't it point to either a bad cable, bad ic22 or something around that, or a bad ULA? (I'd check in that order) it is usually black and white, with possible atributes rasing colors all around.

Dbug is right. If the PSU outputs 12 volt (not measured with a multimeter, but nominally) that is not correct and could have damaged things.

80% of times it is due to ram problems, including the ram multiplexors, so I would also check those.
User avatar
ManicMiner1977
Private
Posts: 7
Joined: Thu Oct 24, 2024 2:23 pm

Re: Hello Everyone. I need your help please 🙏

Post by ManicMiner1977 »

Thanks everyone.

The PSU is original, centre +ive with a multimeter. Open not connected to the Atmos. 12v/3.5A. I thought it quite high for a 9v rated PSU.

I'll try the multiplexers too.

Does anyone know what that c23 cap us for. It is sited just above the AY?

I'll make the checks.

Thank you.
User avatar
ManicMiner1977
Private
Posts: 7
Joined: Thu Oct 24, 2024 2:23 pm

Re: Hello Everyone. I need your help please 🙏

Post by ManicMiner1977 »

Also the voltage regulator has been upgraded to TRACO Power TSN 1-2450A. This was done prior to ne buying it.
User avatar
iss
Wing Commander
Posts: 1706
Joined: Sat Apr 03, 2010 5:43 pm
Location: Bulgaria
Contact:

Re: Hello Everyone. I need your help please 🙏

Post by iss »

ManicMiner1977 wrote: Thu Oct 24, 2024 5:50 pm...
The 12V PSU is OK for short tests only else the 7905 will get very very HOT and when the case is closed then things can go ugly.
The C23 - 47nF is just decoupling one change it but Oric should boot without it.
About the TRACO Power TSN 1-2450A: you have to increase the C21 (the reset cap.) form 1uF to 4.7uF...10uF..22uf - this allows TRACO startup and stable 5V.
User avatar
ManicMiner1977
Private
Posts: 7
Joined: Thu Oct 24, 2024 2:23 pm

Re: Hello Everyone. I need your help please 🙏

Post by ManicMiner1977 »

The Cap @ C21 is 25v 10uF. It looks it has been replaced due to the solder.

I'll take some measurements.
User avatar
ManicMiner1977
Private
Posts: 7
Joined: Thu Oct 24, 2024 2:23 pm

Re: Hello Everyone. I need your help please 🙏

Post by ManicMiner1977 »

iss wrote: Thu Oct 24, 2024 4:16 pm
ManicMiner1977 wrote: Thu Oct 24, 2024 3:09 pm...
Welcome here!
Check: both multiplexers '257 (IC8,IC20), tracks with continuity tester.
Measure the resistance between 5V and GND rails (anywhere but after the 7905) - it should to be ~250 Ohms.
Hi There,

Checked for continuity across the multiplexer main track and they seem OK.

5v is reaching every chip on the board from what I can see.

The resistance between 5v and ground on all caps, chips, etc seems to be 177 Ohms.

Checked all RAM, CPU, ULA, 8337, AY
User avatar
iss
Wing Commander
Posts: 1706
Joined: Sat Apr 03, 2010 5:43 pm
Location: Bulgaria
Contact:

Re: Hello Everyone. I need your help please 🙏

Post by iss »

ManicMiner1977 wrote: Thu Oct 24, 2024 7:24 pm The resistance between 5v and ground on all caps, chips, etc seems to be 177 Ohms.
177 Ohms is bit low but acceptable (maybe TRACO lowers it).
Try with changing the '257.
Is any chip extremely hot?
User avatar
ManicMiner1977
Private
Posts: 7
Joined: Thu Oct 24, 2024 2:23 pm

Re: Hello Everyone. I need your help please 🙏

Post by ManicMiner1977 »

Hi There,

Are you saying to replace the multiplexers first?

Under a thermal camera, most obvious chips are around the 40-50 C. I do notice that the ULA is almost cold @ 26 C and doesn't seem to heat up at all. Is this anything to consider? I see ULA go for around £20+ so don't want to replace unless necessary.

I thought because I have a stable image the ULA is fine. However I am not an Oric Expert.

Cheers mate
User avatar
iss
Wing Commander
Posts: 1706
Joined: Sat Apr 03, 2010 5:43 pm
Location: Bulgaria
Contact:

Re: Hello Everyone. I need your help please 🙏

Post by iss »

ManicMiner1977 wrote: Thu Oct 24, 2024 7:51 pm Are you saying to replace the multiplexers first?
Indeed! It's easy to change the multiplexers.
And yes, ULA was ~5$ but it's already 10$+shipping :( At least It's proven they are good.
User avatar
ManicMiner1977
Private
Posts: 7
Joined: Thu Oct 24, 2024 2:23 pm

Re: Hello Everyone. I need your help please 🙏

Post by ManicMiner1977 »

Cheers mate
User avatar
Vyper68
Flying Officer
Posts: 183
Joined: Mon Sep 22, 2014 4:18 pm
Location: Hurworth, UK
Contact:

Re: Hello Everyone. I need your help please 🙏

Post by Vyper68 »

Don't forget the Oric uses the 2Mhz version 6502A and 6522A not the bog standard 6502 or 6522 used in other computers. You can use a 65c02 with a bodge wire and pin one disconnected.

Can you burn a test EPROM?
Oric Extended Basic V1.1
(C) 1983 Tangerine
37631 Bytes Free
Post Reply