Hello,
I have tried to use both emulators (Oricurtron and Euphoric) with modem.dsk to connect to the pc com port (com 1) tried four machines 2 with win7 and 2 with xp
with pin 2 and 3 connected together on the 9 way dtype
I know you have to edit the config file which I did
for Oricurtron config set to loopback
when I type a character none is returned
Both emulators state they emulate the acia 6551 and is hocked to the pc com port
Also not sure that modem.dsk works ok or not
Is there a tap version for this software or not? unable to locate.
Is there a tool to convert .dsk to .tap?
Once I know that this works I will build a serial card for the oric atmos
Regards
john davis uk
Oricutron and Euphoric with Modem.dsk and RS232
-
- Pilot Officer
- Posts: 80
- Joined: Wed Feb 11, 2015 10:39 am
- Location: uk
- ibisum
- Wing Commander
- Posts: 1646
- Joined: Fri Apr 03, 2009 8:56 am
- Location: Vienna, Austria
- Contact:
Re: Oricurtron and Euphoric with Modem.dsk and RS232
Do you have the machines set up with a Windows terminal, and the chars are received that way across the link, first? This should be verified.
Apropros serial i/o on Oric, I'd love to have working MIDI, which would give a rudimentary networking protocol as well, sufficient to the Oric's needs - i.e. it could be feasible to have a MIDI SYSEX transfer happening to 6 Atmos' wired up to a single Telestrat, with each SYSEX being a new app/tap/dsk to send over the humble wire. I do think the Oric can do a TCP/IP stack, but my interest in MIDI is musical as well. A stack of 6-Atmos in unison mode might sound ridiculous.
Apropros serial i/o on Oric, I'd love to have working MIDI, which would give a rudimentary networking protocol as well, sufficient to the Oric's needs - i.e. it could be feasible to have a MIDI SYSEX transfer happening to 6 Atmos' wired up to a single Telestrat, with each SYSEX being a new app/tap/dsk to send over the humble wire. I do think the Oric can do a TCP/IP stack, but my interest in MIDI is musical as well. A stack of 6-Atmos in unison mode might sound ridiculous.
-
- Pilot Officer
- Posts: 80
- Joined: Wed Feb 11, 2015 10:39 am
- Location: uk
Re: Oricurtron and Euphoric with Modem.dsk and RS232
Hello,
Yes forgot to add using real term on pc (that's not required yet, that's next after loopback works)
What I am doing is loopback so modem.dsk terminal should send character then read it back and it does not
Hope that makes things clear
Regards
john davis uk
Yes forgot to add using real term on pc (that's not required yet, that's next after loopback works)
What I am doing is loopback so modem.dsk terminal should send character then read it back and it does not
Hope that makes things clear
Regards
john davis uk
Re: Oricutron and Euphoric with Modem.dsk and RS232
Oricutron v.1.2 works fine using serial emulation in 'loopback' mode with MODEM.DSK.
After booting with MODEM.DSK you have to configure the hardware (i.e. 1.SETUP LINE).
Than select 9600, 8 bit, no parity, 1 stop bit.
Importatant: base address is #31C!
Flow control is 'none'.
Start the terminal program (i.e. 2.RUN COMM PROG FROM DISK)
Here is how I use it under Linux (in Windows it should be the same!):
Starting emulator from command line:
# ./oricutron -ma --serial loopback disks/MODEM.DSK Then every typed charachter is echoed back: @jdavis6809: is there any special reason to write your messages with so much empty lines - I'm just curious
After booting with MODEM.DSK you have to configure the hardware (i.e. 1.SETUP LINE).
Than select 9600, 8 bit, no parity, 1 stop bit.
Importatant: base address is #31C!
Flow control is 'none'.
Start the terminal program (i.e. 2.RUN COMM PROG FROM DISK)
Here is how I use it under Linux (in Windows it should be the same!):
Starting emulator from command line:
# ./oricutron -ma --serial loopback disks/MODEM.DSK Then every typed charachter is echoed back: @jdavis6809: is there any special reason to write your messages with so much empty lines - I'm just curious
-
- Pilot Officer
- Posts: 80
- Joined: Wed Feb 11, 2015 10:39 am
- Location: uk
Re: Oricutron and Euphoric with Modem.dsk and RS232
hello,
Spaced lines easy for me to read.
I think you misunderstand me.
I want to loopback via com1 port of the pc (pins 2 and 3 of the 9 way dtype connector) within the modem.dsk program.
As you outline config is set to loopback
part of config file for acia
; ACIA emulation back-end name:
; 'none' - no serial present
; 'loopback' - for testing - all TX data is returned to RX
; 'modem[:port][:ipv6]' - emulates com port with attached modem,
; only minimal AT command set is supported and
; data is redirected to TCP. Default port is 23 (telnet).
; if :ipv6 is added at the end uses IPv6 instead of IPv4
; 'com:115200,8,N,1,<device>' - use real or virtual <device> on host as emulated ACIA
; baudrate, data bits, parity and stop bits can be set as needed
; ex.: Windows: 'com:115200,8,N,1,COM1'
; Linux: 'com:115200,8,N,1,/dev/ttyUSB0'
serial = 'modem'
I tried all settings listed above
nothing works
regards
john davis uk
Spaced lines easy for me to read.
I think you misunderstand me.
I want to loopback via com1 port of the pc (pins 2 and 3 of the 9 way dtype connector) within the modem.dsk program.
As you outline config is set to loopback
part of config file for acia
; ACIA emulation back-end name:
; 'none' - no serial present
; 'loopback' - for testing - all TX data is returned to RX
; 'modem[:port][:ipv6]' - emulates com port with attached modem,
; only minimal AT command set is supported and
; data is redirected to TCP. Default port is 23 (telnet).
; if :ipv6 is added at the end uses IPv6 instead of IPv4
; 'com:115200,8,N,1,<device>' - use real or virtual <device> on host as emulated ACIA
; baudrate, data bits, parity and stop bits can be set as needed
; ex.: Windows: 'com:115200,8,N,1,COM1'
; Linux: 'com:115200,8,N,1,/dev/ttyUSB0'
serial = 'modem'
I tried all settings listed above
nothing works
regards
john davis uk
Re: Oricutron and Euphoric with Modem.dsk and RS232
Now it clear what you want to do. Put in config file:
serial=com:115200,8,N,1,COM1
Take care to set the proper number after the up-case 'COM', you can check in Windows 'Device Manager' the actual number.
Than plug loopback dongle in your RS port. Here are variants of what you need: or Setup the program as described in my above post.
There is no relation between selected COM parameters in Oric and the parameters for the real COM.
Happy loopback-ing .
serial=com:115200,8,N,1,COM1
Take care to set the proper number after the up-case 'COM', you can check in Windows 'Device Manager' the actual number.
Than plug loopback dongle in your RS port. Here are variants of what you need: or Setup the program as described in my above post.
There is no relation between selected COM parameters in Oric and the parameters for the real COM.
Happy loopback-ing .