Search found 114 matches

by metadata
Wed Jul 13, 2016 9:16 pm
Forum: General Discussion
Topic: Next Cumulus batch
Replies: 95
Views: 51819

Re: Next Cumulus batch

sorry that i was so long gone.
too much work and too less time for hobbies. :)

good to see that the cumulus is going in the next revision.
by metadata
Wed Jul 13, 2016 2:25 pm
Forum: General Discussion
Topic: Next Cumulus batch
Replies: 95
Views: 51819

Re: Next Cumulus batch

Hi guys. :)
by metadata
Thu Aug 07, 2014 1:22 pm
Forum: General Discussion
Topic: Cumulus Issues
Replies: 358
Views: 93477

Re: Cumulus Issues

Hello, I'm unhappy to say that my Cumulus had stop working. It was used only 2-3 times for about 4-5 minutes since buying it, but now when I tried to start and it is absolutely dead. Is there any support for these devices? does the screen backlight turn on when you power it up? Have you tried to re...
by metadata
Mon Jul 28, 2014 11:02 am
Forum: General Discussion
Topic: Cumulus Issues
Replies: 358
Views: 93477

Re: Cumulus Issues

My PSU is giving 12 V and over 12 VA, not 9 V. it runs Oric and microdisc drive at the same time well. But as you know Cumulus doesn't work.. so your powersupply only have 1A at 12V? And the VA is on the inputside of the supply, right? So you have not 1A output maybe only 60-80% of 1A at the output...
by metadata
Tue Jul 15, 2014 9:33 pm
Forum: General Discussion
Topic: Cumulus Preorder Thread
Replies: 272
Views: 120974

Re: Cumulus Preorder Thread

sorry that you have to wait so long. I have been a little busy the last weeks so i don't had the time to build more cumulus. At the moment my 3D-Printer is not working very good. I printed about 10-15 cases that don't look good and so i descided it's time to buy a new Hotend and Heatbed for better p...
by metadata
Wed May 28, 2014 9:52 pm
Forum: Hardware hacks and extensions
Topic: Microdisc replacement project
Replies: 183
Views: 67908

Re: Microdisc replacement project

The next Cumulusboards are nearly ready and my 3D-Printer is working nonstop :)
by metadata
Wed May 07, 2014 8:52 pm
Forum: General Discussion
Topic: Cumulus Preorder Thread
Replies: 272
Views: 120974

Re: Cumulus Preorder Thread

Dbug wrote:
JamesD wrote:I was contacted but I put off my order to see if some of the problems could be resolved first.
Should I move your order back to the bottom of the page so you get recontacted?
I'm trying to keep the list clear for everybody to know where they are :)
next on my list is dolarfred. :)
by metadata
Mon Apr 28, 2014 3:33 pm
Forum: Hardware hacks and extensions
Topic: Microdisc replacement project
Replies: 183
Views: 67908

Re: Microdisc replacement project

resupply has arrived :)
70 new Culumus PCB's.
by metadata
Tue Apr 22, 2014 3:44 pm
Forum: General Discussion
Topic: Cumulus Preorder Thread
Replies: 272
Views: 120974

Re: Cumulus Preorder Thread

Will it work with Pravetz-8D? Now I need some help to try to fix my Cumulus - what is the purpose of the two connectors inside Cumulus box? If there is UART or RS232 (or JTAG) I need pin description - just to see if there's some response... Oh... sounds not good. But you can try to flash a new boot...
by metadata
Fri Apr 11, 2014 6:23 pm
Forum: General Discussion
Topic: Cumulus Preorder Thread
Replies: 272
Views: 120974

Re: Cumulus Preorder Thread

http://wikitravel.org/en/Electrical_systems

Voltage is the same in UK but the plug is different.
My powersupply has the "Europlug (Type C)" and takes 100-240V as input. Only the UK has a diffenrent plug in europe.
but the seller from the ebaylink is really cheap! :)
by metadata
Fri Apr 04, 2014 1:17 pm
Forum: General Discussion
Topic: Cumulus Issues
Replies: 358
Views: 93477

Re: Cumulus Issues

[ Metadata: What device do you use to program the E(E)PROM? it is parallel based or USB based? ] It's USB based. Genius G840. Nice and no that expensive, are you happy with it? it's okay. it is a lot better than my parallel one. The software for the parallel one only runs under windowsXP. The softw...
by metadata
Fri Apr 04, 2014 12:25 pm
Forum: General Discussion
Topic: Cumulus Issues
Replies: 358
Views: 93477

Re: Cumulus Issues

I've knocked the jumper off the little board that connects to the expansion port. Should it be over the two pins? I don't recall it being over them both. normal the pins are not connected. You can close the jumper and the jumper in the cumulus and then you have to use the black and the grey connect...
by metadata
Thu Apr 03, 2014 1:54 pm
Forum: General Discussion
Topic: Cumulus Issues
Replies: 358
Views: 93477

Re: Cumulus Issues

[ Metadata: What device do you use to program the E(E)PROM? it is parallel based or USB based? ]
It's USB based. Genius G840.
by metadata
Sun Mar 30, 2014 9:29 pm
Forum: Hardware hacks and extensions
Topic: Microdisc replacement project
Replies: 183
Views: 67908

Re: Microdisc replacement project

I worked on the case of the Cumulus a little bit. It now fits better and the PCB don't move any more.
Also i edit the connectors a little bit.
Much better :)

Downloadable at my blog http://www.boriskaminski.de/2014/03/30/ ... haeuse-v8/
by metadata
Fri Mar 28, 2014 7:44 pm
Forum: General Discussion
Topic: Cumulus Preorder Thread
Replies: 272
Views: 120974

Re: Cumulus Preorder Thread

BTW, the screen on my cumulus flicker a bit, like if there were interference on a CRT screen, I am alone on this? this is normal. The lm2660 chip converts the 5V to 7V. Maybe there comes the flickering from. I've just received mine. Unfortunately I'm flat broke so testing (ie, buying a PSU) will ha...